Execute wall stickers according to experts' instructions

In fact, sticking a wall sticker is a much harder task than what we think. You can master the basics with common sense, use the right tools and practice a few times. As with any manual work, new people can make some mistakes, but if you choose the right type of wallpaper for the first time, errors can be overcome, even to avoid making mistakes. completely.

On the advice of experts and the owner of the wallpaper shop, you should avoid buying wallpaper Korea, because usually this type of paper has two layers, the outer layer is water resistant so it is easy to protect birth, cleaning when there are stains.

Extra glue can be wiped clean with a damp cloth and straight so you can easily paste, peel off or glue it.

Prepare the walls by polishing and sanding the surface of the wall like normal water, otherwise the wallpaper will break. Then sweep an oil primer. Just have some basic skills, you can completely paste the wallpaper at home perfectly beautiful.

Some tools to prepare:

1. Rollers (23cm)

2. Natural sponge

3. Corner brush

4. Mini roller (roll eyelid)

5. Acid pump

6. Ruler

7. Blades

8. Knives

9. Pencil

10. Level gauge

11. Ruler

12. Pull

13, 14, 15: Scraps of various sizes

16. Dry towels

Perform:

Step 1: Apply glue on wallpaper

First, cut all strips of wallpaper in the same size. Each side should be 8 - 10 cm.

Pour a glue into a tray, using a roll of glue.

Turn over the sticker and start rolling across the surface.

For easy manipulation when placed on the wall, hiding the middle point and then folded back.

Gently fold the edges evenly, using your hands to gently smooth the surface to glue evenly but do not make too strong to avoid creases.

Wait for about 15 minutes for the resin to dry.

Step 2: Measure and paste

Before applying, use the ruler, pre-measuring the level and pencil mark the border for each strip of wallpaper.

This step helps to accurately position the wallpaper.

Next, place the edge of the strip of wallpaper overlap with the available line. Leave the top 8 - 10 cm so that the piece of paper is beautiful and easy to manipulate. The excess paper will be cut off later. Stick your hands to tighten the wallpaper to it, both horizontally and vertically to the end.

Step 3: Grab the paper strip together

Try to place as long a new wallpaper as close to the original wallpaper as possible.

Note to adjust the pattern to seamless. Wait for about 10 - 15 minutes to seal the glue, running the mini roller along the seam to the edge of the adhesive.

In case the patches of paper do not stack together, they can be offset by a piece of paper underneath to fix the problem.

Step 4: Handle the corners

Many beginners tend to stick paper from top to bottom, covering the edges of the walls. It is easy to make wallpaper sticky, not stick to the wall and easily peeling.

In order to handle the corners of the paper, it is necessary to follow the following steps:

Arrange the next strip of wallpaper overlap about 4 - 5 cm.
For the edge of the window, stick the wall cover on the frame about 5 - 6 cm.

One hand scraper the wall paper close to the frame. The other hand uses small knives slowly slanting along the frame. Remove the waste paper.

Step 5: Handle the electrical outlets

Many people who love the electrical outlet in the room are also glued to the wall to create the synchronization.

Before putting paper on the electrical outlet, remember to disconnect the power supply.

Remove the cover of the power outlet.
Cut a piece of wallpaper larger than the case of the power outlet.

Metal casing usually has better adhesion than plastic casing.

Use a knife to remove any excess pieces of paper, and then fold the edges inward.

Finally, firmly attach the shell to its original position.

So your room is complete, look at some beautiful pictures of wallpaper:

Source: khampha.vn